Phoenix Contact – REL-IR-BL/L- 24DC/2X21 – Single relay
1032526
Plug-in industrial relay with power contacts, 2 changeover contacts, test button, status LED, mechanical switch position indicator, input voltage: 24 V DC
This product needs further products for operation.
Technical data
Notes
|
Notes on operation |
Do not connect adjacent channels to SELV/ PELV and voltages dangerous to the touch. |
|
Notes on operation |
The outputs are not suitable for switching different outer conductors. |
|
Notes on operation |
Do not use to separate SELV / PELV circuits from other circuits, because safe isolation is not guaranteed. |
Product properties
|
Product type |
Single relay |
|
Product family |
ESSENTIAL edition |
|
Operating mode |
100% operating factor |
|
Mechanical service life |
3x 107cycles |
Insulation characteristics: Air clearances and creepage distances between coil and contact side
|
Insulation |
Basic insulation |
|
Overvoltage category |
III |
|
Pollution degree |
2 |
Data management status
|
Date of last data management |
02.06.2025 |
Electrical properties
|
Service life electrical |
see diagram |
|
Maximum power dissipation for nominal condition |
759 mW |
|
Test voltage (Winding/contact) |
2.5 kVrms(50 Hz, 1 min., winding/contact) |
|
Test voltage (Changeover contact/changeover contact) |
2.5 kVrms(50 Hz, 1 min., changeover contact/changeover contact) |
Air clearances and creepage distances between coil and contact side
|
Rated insulation voltage |
250 V AC |
|
Rated surge voltage |
5 kV |
Input data
Coil side
|
Nominal input voltage UN |
24 V DC |
|
Input voltage range |
19.2 V DC … 40.8 V DC (20 °C) |
|
Drive and function |
monostable |
|
Drive (polarity) |
polarized |
|
Typical input current at UN |
32 mA |
|
Typical response time |
15 ms |
|
Typical release time |
10 ms |
|
Coil voltage |
24 V DC |
|
Status display |
Yellow LED (bidirectional) |
Output data
Switching
|
Contact switching type |
2 changeover contacts |
|
Type of switch contact |
Single contact |
|
Contact material |
AgNi |
|
Maximum switching voltage |
250 V AC/DC |
|
Minimum switching voltage |
12 V (10 mA) |
|
Limiting continuous current |
12 A |
|
Maximum inrush current |
24 A (20 ms, N/O contacts) |
|
Min. switching current |
10 mA (12 V) |
|
Interrupting rating (ohmic load) max. |
288 W (24 V DC) |
|
130 W (48 V DC) |
|
|
90 W (60 V DC) |
|
|
66 W (110 V DC) |
|
|
88 W (220 V DC) |
|
|
3000 VA (250 V AC) |
|
|
Switching capacity min. |
120 mW |
Connection data
|
Connection method |
Plug-in connection |
Dimensions
|
Width |
22.5 mm |
|
Height |
28 mm |
|
Depth |
35.5 mm |
Environmental and real-life conditions
Ambient conditions
|
Degree of protection |
RT II |
|
Degree of protection (Installation location) |
≥ IP54 (Installation location) |
|
Ambient temperature (operation) |
-40 °C … 70 °C |
|
Ambient temperature (storage/transport) |
-40 °C … 70 °C |
|
Altitude |
≤ 2000 m |
Standards and regulations
Air clearances and creepage distances between coil and contact side
|
Standards/regulations |
EN 61810-1 |
Mounting
|
Mounting type |
Plug-in mounting |
|
Assembly note |
in rows with zero spacing |
|
Mounting position |
any |
Commercial data
|
Item number |
1032526 |
|
Packing unit |
10 pc |
|
Minimum order quantity |
10 pc |
|
Sales key |
CK6 |
|
Product key |
DKF943 |
|
GTIN |
4055626536071 |
|
Weight per piece (including packing) |
30.176 g |
|
Weight per piece (excluding packing) |
30.176 g |
|
Customs tariff number |
85364900 |
|
Country of origin |
AT |
Related products
-
Oxygen Rich Side Blown Melt Melting Furnace
Contact UsThe oxygen rich side blown molten pool melting furnace is an efficient and energy-saving steel melting equipment. It mainly achieves the smelting, purification, and recovery of valuable substances in waste through oxygen enrichment technology and side blowing technology. Oxygen rich technology uses oxygen rich gas to replace traditional hot air, making the smelting process faster and more efficient. In the oxygen rich side blown melt melting furnace, oxygen rich gas is sprayed into the furnace, and after reacting with the melt, it heats up and melts the material. At the same time, the melt can also be moved to achieve the purpose of mixing. Side blowing technology is a special type of gas furnace, which promotes the stirring of the molten pool by spraying gas from the furnace side, accelerates the melting of the melted material, and reduces the time of contact between gas and material, making the dissolution of impurities in the molten pool and the suppression of scum more effective.
-
UT 1.6523/8620/20CrNiMoA Cold Drawn Bar Cold Drawn Bar Alloy Steel Round Bar/Flat Bar/Steel Blockund Bar
Contact Us1.6523 Cold Drawn Bar Cold Drawn Bar Alloy Steel Round Bar/Flat Bar/Steel Block/Round Bar
-
LFQ1300 Micro Computer Controlling Slitting Machine
Contact UsLFQ1300 Micro Computer Controlling Slitting Machine
-
Capacity 1258ML Hot Filling Suitable For Krones Machine
Contact UsBottle Volume: 1258ml
Bottle Type: hot-filling bottle
Suitable Equipment: Krones
Packing Method: Standard packing for export.
Reviews
There are no reviews yet.